Skip to content

A named system, with its lights listed

Godox X5F for Fujifilm, Godox 2.4G X system

A 20 € transmitter that belongs to a named system — Godox 2.4G X — fires the maker’s studio heads by name, and has no power switch and no channel count.

Godox X5F flash trigger in black, a small hot shoe unit with a locking ring

Godox X5F for Fujifilm, Godox 2.4G X system

A 20 € transmitter that belongs to a named system — Godox 2.4G X — fires the maker’s studio heads by name, and has no power switch and no channel count.

Radio system named
The Godox 2.4G X system, named in the title and the third bullet, which then lists what it reaches: the AD100Pro II, AD200Pro II, AD600Pro II, AD600BM II, iT30Pro, V100, V480 and the Lux Master models. This is exactly what the hub above asks for — a system named on the box, with the lights that speak it enumerated, so the consequences of the purchase are visible before it is made
Camera mounts supported
Fujifilm, named in the title and listed body by body in the second bullet: X-Pro2, X-T20, X-T2, X-T1, GFX50s, GFX50R, X-T30, X-T4, X-T3, X-S20, X-T5, X-Pro1, X-T10, X-E1, X-A3, X100F and X100T. One camera system, named explicitly — which is the gate the hub above describes, since the contacts behind the centre pin differ between makers
Channel and group counts
Not published. Five bullets name the system, the cameras, the compatible lights, the mounting and the battery, and no channel or group figures appear. The cheapest trigger on this shelf publishes 16 channels; this one publishes none, which is the odd gap on an otherwise precise page
Remote power control
Yes, but narrowly, and the third bullet is careful about it: used off-camera the X5F can adjust the power of the iT32 only. It will fire other Godox X-system lights and cannot change their power levels. That is a real limitation stated plainly rather than left to be discovered
Metering and sync modes claimed
High-speed sync support, named in the first bullet, and TTL in the product description. No sync ceiling in fractions of a second is published here — the flash it partners quotes 1/8000 s — and no metering protocol is named beyond TTL for Fujifilm
Power source
A built-in 3.8 V 100 mAh lithium cell that charges only when the unit is attached to the iT32, about 3 hours to fill, giving up to 16 hours of standby. The closing bullet also states there is no physical power switch: status is shown by coloured LEDs, and the charge level appears in the flash’s own menu
Amazon reference
B0G25HKMXQ (same reference on 6 Amazon marketplaces)
EAN
0767637542913
  • A named system with its compatible lights listed by model, from the AD100Pro II to the V480
  • Fujifilm bodies named individually rather than described as universal
  • No channel or group counts published anywhere

Best for: A Fujifilm body already inside the Godox X system, where the named light list is the reason to buy and the iT32 is the flash it drives.

≈ $20 / £18 / 20 €
Check price on Amazon

Specifications

Radio system named
The Godox 2.4G X system, named in the title and the third bullet, which then lists what it reaches: the AD100Pro II, AD200Pro II, AD600Pro II, AD600BM II, iT30Pro, V100, V480 and the Lux Master models. This is exactly what the hub above asks for — a system named on the box, with the lights that speak it enumerated, so the consequences of the purchase are visible before it is made
Camera mounts supported
Fujifilm, named in the title and listed body by body in the second bullet: X-Pro2, X-T20, X-T2, X-T1, GFX50s, GFX50R, X-T30, X-T4, X-T3, X-S20, X-T5, X-Pro1, X-T10, X-E1, X-A3, X100F and X100T. One camera system, named explicitly — which is the gate the hub above describes, since the contacts behind the centre pin differ between makers
Channel and group counts
Not published. Five bullets name the system, the cameras, the compatible lights, the mounting and the battery, and no channel or group figures appear. The cheapest trigger on this shelf publishes 16 channels; this one publishes none, which is the odd gap on an otherwise precise page
Remote power control
Yes, but narrowly, and the third bullet is careful about it: used off-camera the X5F can adjust the power of the iT32 only. It will fire other Godox X-system lights and cannot change their power levels. That is a real limitation stated plainly rather than left to be discovered
Metering and sync modes claimed
High-speed sync support, named in the first bullet, and TTL in the product description. No sync ceiling in fractions of a second is published here — the flash it partners quotes 1/8000 s — and no metering protocol is named beyond TTL for Fujifilm
Power source
A built-in 3.8 V 100 mAh lithium cell that charges only when the unit is attached to the iT32, about 3 hours to fill, giving up to 16 hours of standby. The closing bullet also states there is no physical power switch: status is shown by coloured LEDs, and the charge level appears in the flash’s own menu
Amazon reference
B0G25HKMXQ (same reference on 6 Amazon marketplaces)
EAN
0767637542913

On the listing

Five bullets. A TTL wireless trigger for Fujifilm on 2.4 GHz, made for the iT32 mini flash, with high-speed sync support, an integrated battery and a colour status indicator; a compatibility list naming Fujifilm bodies from the X-Pro2 and GFX50s through the X-T5 to the X100T; the Godox 2.4G X system, with the X5F able to fire the AD100Pro II, AD200Pro II, AD600Pro II, AD600BM II, iT30Pro, V100, V480 and Lux Master units, and a note that off-camera it can adjust only the iT32’s power; magnetic attachment under the iT32 with a locking ring for the camera shoe; and a closing warning that there is no physical power switch, that the 3.8 V 100 mAh cell charges only when connected to the iT32, taking about 3 hours for up to 16 hours of standby.

A system with its lights listed

Seven models named, and that is the whole value of the page. The hub above says to choose the system before the trigger, because every light bought afterwards has to speak it. A page that enumerates the AD100Pro II through to the V480 lets that decision be made with the facts in view.

Seventeen Fujifilm bodies, named

Not universal, not most cameras: a list. The shoe contacts differ between makers, and a transmitter is sold per system for that reason. Naming the bodies is how a buyer avoids the mismatch that passes only the bare fire signal.

What it will not do off-camera

Fire other lights, yes. Change their power, no. The third bullet states it in the middle of a paragraph about capability, which is where such a limit is easiest to miss and most needs reading.

No switch, and a cell that only fills on the flash

Sixteen hours of standby, three hours to charge, and charging happens solely when the trigger is magnetically docked to the iT32. It is a coherent design for a two-piece kit, and it means neither half travels usefully alone.

Availability

About 20 € on the German, French, Italian and Spanish Amazon stores when this page was last checked.

The American and British Amazon stores carry it too, priced in local currency. Those amounts are deliberately absent from the range above, which reads euro stores only.

Everything in this section is the figure Keepa carried on the day of the last update to this page. Availability and prices shift without notice.

Prices quoted in this text were read on 13 September 2026. The live price is at the top of the page.

What this fits

More flash triggers

  • NEEWER QZ-N flash trigger with a touchscreen display on a camera hot shoe

    NEEWER QZ-N, 2.4G Q system, touchscreen, 1/8000 s

    The dearest trigger here at 93 €, with a touchscreen, five groups, thirty-two channels, remote power from 1/256 to 1/1 and high-speed sync to 1/8000 — and it fires Godox lights as well as its own.

    Radio system named
    The NEEWER 2.4G Q system, with its own lights listed — Z3R-N, Z2PRO-N, Z2-N, Z1-N, Z880-N, NW760-N, S101-400W Pro, S102-400W Pro, Q4, Q4PRO, Q6, Q300, Q200 and Q120 — and then the unusual part: Godox iT32, V1 and V100 flashguns and the AD200 Pro II and AD100 Pro II outdoor heads are supported too, with current firmware. A named system that also reaches into a rival’s is rare, and the Q6 head in this catalogue is among the lights it drives
    Camera mounts supported
    Nikon, listed at length in the closing bullet — Z9, Z8, Zfc, Z50, Z30, Z5, Z6, Z7, Z6 II, Z7II and reflex bodies from the D4 and D5 to the D7500 — with one explicit exclusion: not compatible with the D810. An exclusion stated plainly is worth more than a list that implies everything works
    Channel and group counts
    5 groups, 32 channels and IDs from 01 to 99, with channel search, over a range given as 328 feet — about 100 m. It is the most granular addressing on this shelf: groups to control lights separately, channels to avoid others, and IDs to separate two photographers using the same channel
    Remote power control
    Yes, in full: flash power from 1/256 to 1/1, plus or minus 3 EV of exposure compensation, modelling light control and group control, all from the touchscreen. The second bullet adds automatic or manual zoom from 20 to 200 mm, which sets the beam of a compatible flash from the transmitter
    Metering and sync modes claimed
    TTL, manual and strobe, with 1/8000 s high-speed sync and S1 and S2 optical modes, in the first two bullets. The first carries a working note: the single-contact mode must be disabled for TTL and strobe to function. It is the only trigger on this shelf claiming metering and high-speed sync at all
    Power source
    A 1000 mAh lithium cell, fully charged in 2.5 hours, with a real-time battery display and firmware upgrades, in the fourth bullet. The same bullet gives the forced shutdown gesture — hold the power and test buttons together — which is the kind of detail that only appears after people have needed it
    Amazon reference
    B0G4QVWJTX (same reference on 6 Amazon marketplaces)
    EAN
    0191073129207
    • Five groups, 32 channels and 99 IDs, the most complete addressing on this shelf
    • Remote power from 1/256 to 1/1, exposure compensation, modelling light and zoom from 20 to 200 mm
    • Ninety-three euros, more than four times the 17 € Andoer

    Best for: A Nikon body running several NEEWER Q or compatible Godox lights, where power, zoom and modelling light are set from a touchscreen rather than at each head.

    ≈ $84 / £80 / 93 €
    Check price on Amazon
  • VBESTLIFE flash trigger transmitter and receiver pair in black with a sync adapter

    VBESTLIFE 16 channels on 433 MHz, transmitter and receiver

    A transmitter and receiver set at 20 € offering 16 channels, a 1/250 s sync claim and a jack adapter — and naming a radio frequency where every other trigger here names a system.

    Radio system named
    None — the third bullet gives a working frequency of 433 MHz, which is not the same thing. The hub above says each trigger belongs to a system named on the box, and that the system decides which flashes can ever join the set. A frequency says which band the radio uses; it does not say who can talk to whom. Nothing on this page names a protocol, so compatibility begins and ends with the receiver in the box
    Camera mounts supported
    Pentax is named in the second bullet, which credits the transmitter with a unique contact design suited to Pentax and other cameras. The fourth bullet adds a 3.5 mm to 6.35 mm adapter for studio flashes, and the shoe carries the fire signal only — so on any camera it will trigger, and it will pass nothing else
    Channel and group counts
    16 channels, in the title and the first bullet, credited with strong interference resistance. No groups are published, which is the distinction the hub above draws: channels keep two photographers out of each other’s way, groups let one photographer control lights separately. This set offers the first and not the second
    Remote power control
    None. Nothing on the page describes adjusting a flash from the transmitter, so every light in the set is set by hand at the light — which is what the hub above calls the difference between a trigger and a controller
    Metering and sync modes claimed
    A highest sync speed of 1/250 s, in the third bullet. No through-the-lens metering and no high-speed sync is claimed, and no mode is named — so the claim is for ordinary sync at a stated ceiling, which is an honest position for a 20 € set
    Power source
    The receiver takes two AAA cells, not supplied, named in the fifth bullet with low consumption and long life. The transmitter’s power is not stated
    Amazon reference
    B07THWWJWS (same reference on 5 Amazon marketplaces)
    EAN
    0715990757208
    • Sixteen channels and a claimed 30 m range for 20 €
    • A 3.5 mm to 6.35 mm adapter in the box, so it reaches studio heads with either socket
    • A frequency named instead of a system, so nothing can be said about what else will ever join the set

    Best for: Firing one or two manual studio heads on a budget, where the set that arrives in the box is the whole system and will stay that way.

    ≈ £21 / 20 €
    Check price on Amazon
  • Walimex pro flash trigger, a small black transmitter for a camera hot shoe

    Walimex pro Walimex pro trigger, 16 channels, 4 groups, 25 g

    The one trigger here that controls its lights as well as firing them — modelling light and flash power from the camera, across 16 channels and 4 groups, for 34 €.

    Radio system named
    Named by the lights rather than by a protocol: the second bullet says it is for the Walimex pro VE, VC and Newcomer series and connects directly to the receivers built into those heads, so no separate receivers or cables are needed. The first bullet gives a stable 2.4 GHz link. That is a closed and clearly stated system — narrower than the Godox or NEEWER ecosystems, and unambiguous about what it drives
    Camera mounts supported
    Any shoe with a centre contact, per the fourth bullet, which names the centre contact as the means of firing. No camera system is named and none is excluded, which follows from the fact that nothing but the fire signal needs to pass — the control it offers goes to the lights, not through the camera
    Channel and group counts
    16 channels and 4 groups, in the third bullet, which explains what they are for: organising several heads into groups and using channels to keep multiple systems apart in a larger studio. Both numbers, and the reason for each — the only page on this shelf to do that
    Remote power control
    Yes, and it is the fifth bullet’s whole subject: the trigger fires the flashes and also controls functions such as the modelling light and the flash power, which the bullet says suits ceiling rail systems and heads that are hard to reach. This is the capability the hub above names as the reason to want a transmitter rather than a fire button
    Metering and sync modes claimed
    Sync to 1/160 second, in the fourth bullet. No metering and no high-speed sync is claimed. It is the lowest sync ceiling on this shelf — the two cheap sets claim 1/250 s — and it is stated plainly alongside a claim that it suits movement
    Power source
    Not published on the listing. The fourth bullet gives a weight of 25 grams and describes the unit as compact on the camera shoe, and no cell type appears anywhere
    Amazon reference
    B00I48K7D0 (same reference on 6 Amazon marketplaces)
    EAN
    4250234598996
    • Remote control of flash power and the modelling light, not just firing — the only trigger here that does both
    • 16 channels and 4 groups, with the purpose of each explained
    • Sync at 1/160 s, the lowest ceiling on this shelf

    Best for: A studio already built on Walimex pro heads, especially on ceiling rails, where reaching a light to change its power is the daily nuisance this solves.

    ≈ 30 €
    Check price on Amazon

Elsewhere in the camera bag

  • Lightdow folding grey card opened to 30 by 30 cm beside its carry case

    Lightdow 30 by 30 cm folding, 17.8 % reflectance, density 0.74

    Eleven euros for a 30 by 30 cm pop-up card that publishes 17.8 per cent, a density of 0.74, a 2 per cent tolerance and an eighth of a stop of error — the only measured card here.

    Reference type
    A DOUBLE-SIDED POP-UP card — grey on one face, white on the other, in the fourth bullet, which says it simplifies the technical questions of exposure and colour correction under varying light and names weddings and fashion shows as where that matters. It springs open like a reflector rather than being a rigid card
    Stated reflectance
    17.8 PER CENT, in the first bullet — and the honesty of that figure is the point. "Eighteen per cent" is the nominal standard; 17.8 is what this surface actually measures, published alongside a DENSITY OF 0.74. Density is the logarithmic form of the same property, and giving both is how a manufacturer shows the figure came from an instrument rather than a catalogue
    Patch count and published values
    Two faces, no patches. What it publishes instead is unique on this shelf: a MAXIMUM DEVIATION OF 2 PER CENT in the second bullet, and a MAXIMUM METERING ERROR OF ONE EIGHTH OF A STOP in the third. A tolerance is what turns a claim into a specification
    Surface finish
    Not described — the one gap on an otherwise measured page. The 11 € JJC here publishes non-reflective, and on a 30 cm surface a sheen matters more rather than less
    Size
    30 by 30 cm, in the title — NEARLY SEVEN TIMES the area of the 130 by 100 mm cards on this shelf, and FOLDING, with a carry case supplied. A large target can be metered from further away and photographed in the frame for later correction; a folding one still fits in a bag
    Supplied case
    YES — a carry case, in the title and the fourth bullet, which is what a sprung folding card needs. The fifth bullet adds a 90-day return and replacement guarantee for quality-related problems
    Amazon reference
    B00HT9MA1W (same reference on 6 Amazon marketplaces)
    EAN
    0616983848487
    • Seventeen point eight per cent and a density of 0.74, both published
    • A 2 per cent deviation and an eighth of a stop of metering error — the only tolerances here
    • The surface finish is never described, on the largest card here

    Best for: Metering from a distance at a wedding or a show, where the card has to be large, fold away and be trusted to a fraction of a stop.

    ≈ $15 / £13 / 11 €
    Check price on Amazon
  • Belmalia set of eight black anodised step-up rings laid out in order of size

    Belmalia Eight step-up rings, 49 to 82 mm

    Eight anodised rings from 49 to 82 mm for 11 €, each stepping up one size, and screwable into one another to reach the gaps between.

    Mounts joined
    NONE — and this is the distinction the word "adapter" hides on this shelf. These are filter-thread rings: they join a larger filter to a smaller lens thread, in eight steps from 49 to 82 mm. No camera mount is involved at any point. The 95 € Canon and the 185 € Nikon on this shelf are the mount adapters; three of the five pages here, this one included, are rings
    Contacts present
    None, and none is possible: a filter ring sits at the front of the lens, where there is nothing to communicate with
    Functions claimed
    One: fitting. The first bullet says larger filters or converters can be used on lenses of smaller diameter, and that is the whole claim. Nothing is passed, nothing is powered, nothing is lost
    Optical elements
    None. The rings are hollow metal, which is why they cost 11 € and change nothing about the image — the intro above reserves corrective elements for adapters working against the flange distance
    Tripod foot
    Not applicable
    Aperture ring
    Not applicable
    Build
    Anodised aluminium, in the third bullet, described as stable, dimensionally true and light. The fourth bullet claims precisely cut threads that neither tilt nor jam, and the second says the rings screw into one another to reach intermediate sizes — 49 to 58 through two rings, for instance
    Amazon reference
    B00OE7B0UE (same reference on 6 Amazon marketplaces)
    EAN
    4054438653150
    • Eight consecutive steps from 49 to 82 mm, with no gap left in the sequence
    • Anodised aluminium rather than plastic, at 11 € for the set
    • Steps UP only: a smaller filter cannot be put on a larger lens with these

    Best for: One set of large filters shared across several lenses, where every thread in the bag is 49 mm or more.

    ≈ £8 / 11 €
    Check price on Amazon
  • CamKix nine step-up rings arranged from 37 mm to 82 mm

    CAMKIX Nine step-up rings, 37 to 82 mm

    Nine rings from 37 to 82 mm for 11 €, one more step than the Belmalia set at the same price, and the extra one is at the small end where kit lenses live.

    Mounts joined
    NONE. Like the 11 € Belmalia and the 23 € K&F on this shelf, this is a filter-thread set: nine rings that let a larger filter sit on a smaller lens. The mount adapters here are the 95 € Canon and the 185 € Nikon, and they do a different job entirely
    Contacts present
    None, and none is possible at the front of a lens
    Functions claimed
    One, and the first bullet puts it as an economy rather than a feature: a new lens of a different diameter does not require a second set of filters. The second bullet states the mechanism — a larger filter onto a smaller thread
    Optical elements
    None
    Tripod foot
    Not applicable
    Aperture ring
    Not applicable
    Build
    Resistant anodised aluminium, in the fourth bullet, with the claim that these last much longer than plastic adapter rings. No stacking is mentioned anywhere — the 11 € Belmalia set advertises screwing its rings together, and this page leaves the possibility unstated
    Amazon reference
    B077XGL35R (same reference on 6 Amazon marketplaces)
    EAN
    0711099326055
    • Nine steps from 37 mm, covering the small threads an eight-ring set misses
    • The same 11 € as the Belmalia set for one ring more
    • Steps up only, like every ring set that is not the 23 € K&F here

    Best for: A bag mixing a small prime or kit zoom with larger lenses, where the 37 mm end is the thread that actually needs adapting.

    ≈ $12 / £9 / 11 €
    Check price on Amazon

All flash triggers