Skip to content

Every figure published, including the lid depth

HMF ODK100, 30.5 by 23 by 14 cm inside, IP67, 1.82 kg

Forty euros for an IP67 case that publishes everything: 30.5 by 23 by 14 cm inside, split 10.5 and 3.5 between base and lid, three foam layers, 1.82 kg.

HMF ODK100 hard case open showing its pick-and-pluck grid foam

HMF ODK100, 30.5 by 23 by 14 cm inside, IP67, 1.82 kg

Forty euros for an IP67 case that publishes everything: 30.5 by 23 by 14 cm inside, split 10.5 and 3.5 between base and lid, three foam layers, 1.82 kg.

Internal dimensions
THE MOST COMPLETE FIGURES IN THIS CATALOGUE: 30.5 by 23 by 14 cm inside, and the fifth bullet goes further by splitting the depth — 10.5 cm in the base, 3.5 cm in the lid — inside an exterior of 34 by 29.5 by 15.5 cm measured INCLUDING the handle and catches. The split is what tells you whether a body with a lens fitted stands up in the base
Ingress rating
IP67, in the second bullet: dust-tight, and protected against immersion in water to one metre for thirty minutes. It is a standard rather than an adjective, and both cases on this shelf publish it
Interior type
THREE LAYERS, itemised in the third bullet: 95 mm of pre-cut grid foam — the pick-and-pluck kind, plucked cube by cube to the shape of the equipment — a 10 mm foam floor beneath it, and CONVOLUTED egg-crate foam in the lid to press down on whatever is below
Pressure valve
YES, a pressure-equalisation valve in the fourth bullet. A sealed case carried up a mountain or flown in a hold arrives at a different air pressure from the one it was closed at, and without a valve the lid either jams shut or strains its seal
Latch and lock provision
A folding carry handle and EYES FOR PADLOCKS, in the fourth bullet. Padlock eyes are what let a case be checked into a hold or left in a vehicle
Wheels and handles
A folding handle, no wheels — correct at this size. Thirty-four centimetres and 1.82 kg is a case that is carried
Empty weight
1.82 kg, PUBLISHED in the fifth bullet — the only empty weight on this shelf, and the figure that decides what an airline allowance leaves for the equipment
Amazon reference
B08K3JBWP7 (same reference on 5 Amazon marketplaces)
EAN
4010537103422
  • Internal dimensions published with the base and lid depths split out
  • Three foam layers named — pick-and-pluck, floor and convoluted lid
  • No wheels, though at 34 cm none is needed

Best for: A body, two lenses and a drone taken somewhere wet, dusty or airborne, where the case has to be locked and its weight declared.

≈ £34 / 40 €
Check price on Amazon

Specifications

Internal dimensions
THE MOST COMPLETE FIGURES IN THIS CATALOGUE: 30.5 by 23 by 14 cm inside, and the fifth bullet goes further by splitting the depth — 10.5 cm in the base, 3.5 cm in the lid — inside an exterior of 34 by 29.5 by 15.5 cm measured INCLUDING the handle and catches. The split is what tells you whether a body with a lens fitted stands up in the base
Ingress rating
IP67, in the second bullet: dust-tight, and protected against immersion in water to one metre for thirty minutes. It is a standard rather than an adjective, and both cases on this shelf publish it
Interior type
THREE LAYERS, itemised in the third bullet: 95 mm of pre-cut grid foam — the pick-and-pluck kind, plucked cube by cube to the shape of the equipment — a 10 mm foam floor beneath it, and CONVOLUTED egg-crate foam in the lid to press down on whatever is below
Pressure valve
YES, a pressure-equalisation valve in the fourth bullet. A sealed case carried up a mountain or flown in a hold arrives at a different air pressure from the one it was closed at, and without a valve the lid either jams shut or strains its seal
Latch and lock provision
A folding carry handle and EYES FOR PADLOCKS, in the fourth bullet. Padlock eyes are what let a case be checked into a hold or left in a vehicle
Wheels and handles
A folding handle, no wheels — correct at this size. Thirty-four centimetres and 1.82 kg is a case that is carried
Empty weight
1.82 kg, PUBLISHED in the fifth bullet — the only empty weight on this shelf, and the figure that decides what an airline allowance leaves for the equipment
Amazon reference
B08K3JBWP7 (same reference on 5 Amazon marketplaces)
EAN
4010537103422

On the listing

Five bullets. Versatile, ideal for transporting sensitive items such as lenses, cameras, measuring instruments or drones; robust, a very stable camera case in impact-resistant plastic with foam, waterproof and dustproof to IP67; individually customisable with one 95 mm pre-cut grid foam, one 10 mm foam floor and convoluted foam in the lid; well considered, with practical handling from a folding carry handle, a pressure-equalisation valve and eyes for padlocks; and dimensions — exterior 34 by 29.5 by 15.5 cm including handle and catches, interior 30.5 by 23 by 14 cm with a base height of 10.5 cm and a lid height of 3.5 cm, and a weight of 1.82 kg.

The base is ten and a half centimetres, not fourteen

No other case in this catalogue splits the depth. Fourteen centimetres in total, 10.5 of it where equipment actually stands. That is the figure that answers whether a body with a lens fitted goes in upright.

Three layers of foam, each named

Ninety-five millimetres of pluckable grid, a 10 mm floor, and convoluted foam in the lid pressing down from above.

IP sixty-seven, which is a standard

Dust-tight, and immersion to a metre for half an hour. Not an adjective — a test.

A valve, because air pressure changes

A case closed at sea level and opened on a mountain either resists or strains. The valve equalises it.

One point eight two kilograms, published

The only empty weight on this shelf. On a flight it is what the allowance has left after the case itself.

Availability

Between 40 € and 44 € on the German, French, Italian and Spanish Amazon stores when this page was last checked.

The British Amazon store carry it too, priced in local currency. Those amounts are deliberately absent from the range above, which reads euro stores only.

Nothing came back from the American Amazon store at all, so the button for that country runs a search instead of opening an entry that is not there.

Everything in this section is the figure Keepa carried on the day of the last update to this page. Availability and prices shift without notice.

Prices quoted in this text were read on 13 September 2026. The live price is at the top of the page.

More camera hard cases

  • B&W International yellow Type 4000 case open with its cubed foam layers

    B&W International Type 4000, IP67, −30 to +80 °C, stackable

    A hundred euros for an IP67 polypropylene case rated from −30 to +80 °C, stackable, with three layers of cubed foam and two 7 mm padlock eyes.

    Internal dimensions
    NOT PUBLISHED, and it is the one specification this page owes. The 40 € HMF on this shelf publishes its interior, its exterior AND the split between base and lid; this page describes the foam that fills a space it never measures
    Ingress rating
    IP67, in the third bullet — dust-tight and protected against immersion to one metre for thirty minutes, the same standard as the HMF here
    Interior type
    THREE LAYERS of pre-cut CUBED foam, in the first bullet, plucked cube by cube to fit a camera, a drone, tools, electronics or measuring equipment, with lid and base foam completing the protection. Three layers is more material to work with than the single 95 mm block of the 40 € HMF
    Pressure valve
    YES, and AUTOMATIC, in the third bullet — paired there with the temperature range, which is the right pairing: air expands and contracts with heat as well as altitude, and a valve is what keeps the seal from doing the work
    Latch and lock provision
    TWO sturdy front catches holding the case closed, and TWO EYES OF 7 mm DIAMETER for padlocks, in the fifth bullet. Publishing the eye diameter is unusual and useful: it says which padlock will actually pass through
    Wheels and handles
    A RUBBERISED carry handle, in the fourth bullet, and a STACKABLE construction that saves space in a vehicle, a store or on a shelf. No wheels. Stackability is a working feature — cases that stack are cases that travel in a van without sliding
    Empty weight
    Not published, where the 40 € HMF gives 1.82 kg
    Amazon reference
    B00H3R5Z5S (same reference on 6 Amazon marketplaces)
    EAN
    0013039312914
    • Rated from −30 to +80 °C, the only temperature range in this catalogue
    • Three layers of cubed foam, with lid and base foam as well
    • No internal dimensions published, at 100 €

    Best for: Equipment that travels in a vehicle through real cold or real heat, stacked with other cases and padlocked.

    ≈ £117 / 100 €
    Check price on Amazon

Elsewhere in the camera bag

  • K&F Concept rain cover with its clear TPU window over a camera screen

    K&F CONCEPT 19 by 15 by 39 cm, TPU window, anti-fog

    Thirty-nine centimetres of depth, a TPU window with an anti-fog coating and a waterproof zip — the most thoroughly built cover on this shelf, at 20 €.

    Lens length accommodated
    THE DEEPEST CAPACITY HERE: 19 by 15 by 39 cm — width, height and depth — in the first bullet, which also asks the buyer to check the measurements before purchase. Thirty-nine centimetres of depth takes a long telephoto with a hood, and publishing all three dimensions is what lets a fat lens be checked as well as a long one
    Eyepiece design
    A HIGH-TRANSPARENCY TPU WINDOW over the display and the viewfinder, in the third bullet, with an ANTI-FOG COATING that prevents condensation forming even when the temperature changes, and a scratch- and oil-resistant surface. The anti-fog layer is unique on this shelf and it addresses the failure that actually happens: a cover in the rain is warm inside and cold outside, and a plain plastic window mists over exactly when it is needed
    Hand access
    Not described. The cover is closed by a zip and adjusted by velcro inside, and how the hands reach the controls is not stated
    Material and seams
    Water-repellent NYLON with a WATERPROOF ZIP, in the second bullet, said to protect against rain, snow, salt air and extreme weather. The zip is the part worth noting — an ordinary zip is a line of holes, and a waterproof one is a real construction choice. Seams are not described
    Closure method
    Three mechanisms, in the second and fourth bullets: the waterproof zip; an ADJUSTABLE VELCRO STRIP INSIDE that adapts to any lens diameter; and elastic bands with a NON-SLIP LEATHER TAB at the lens mount. The internal velcro is what makes one cover fit a 50 mm prime and a 300 mm zoom equally tightly
    Packed size
    Not a figure, but the fifth bullet states the property: light, foldable nylon that takes up hardly any space, named for hiking, action photography and demanding outdoor use
    Amazon reference
    B0F48271FG (same reference on 5 Amazon marketplaces)
    EAN
    6942052558327
    • Nineteen by 15 by 39 cm published — all three dimensions, 39 cm of depth
    • A TPU window with an anti-fog coating, unique on this shelf
    • Hand access is never described

    Best for: A long lens in sustained rain or salt air, where the window must not fog and the cover must grip whatever lens is fitted.

    ≈ £18 / 20 €
    Check price on Amazon
  • NEEWER PB020 camouflage rain cover over a telephoto lens on a tripod

    NEEWER PB020, 950 by 850 mm, 400 mm lens, 150 g, reversible camo

    A 950 by 850 mm nylon sheet at 150 g that reverses between two camouflage patterns and takes a 400 mm telephoto — a 950 by 850 mm sheet at 150 g, at 37 €.

    Lens length accommodated
    THE LONGEST ON THIS SHELF: lenses up to 400 mm in the title, with the third bullet putting camera and lens combined UNDER 600 mm. Those are focal lengths rather than centimetres — a 400 mm telephoto is roughly 35 cm of barrel — and a cover cut for one is a cover for wildlife work
    Eyepiece design
    Not described, and on this cover it matters less: a 950 by 850 mm sheet is draped and folded rather than fitted, so the photographer looks in under the edge rather than through a window
    Hand access
    AN ENLARGED OPENING, in the fourth bullet, giving access to the important camera functions without removing the cover. It is the only page on this shelf to describe hand access at all — four others leave it unstated
    Material and seams
    NYLON, waterproof, in the fifth bullet, credited with long-lasting protection. Seams are not described
    Closure method
    VELCRO fasteners, in the fourth bullet: the cover is pulled over the equipment and the velcro secures it. Simple, adjustable to any size, and the reason the same sheet fits a 200 mm and a 400 mm lens
    Packed size
    Not published as a folded figure — but the WEIGHT is: 150 g, in the fifth bullet, the only weight on this shelf. A hundred and fifty grams of nylon folds to about the size of a fist, which is what the same bullet means by easy to fold and perfect for photography on the move
    Amazon reference
    B0CTCXY92S (same reference on 6 Amazon marketplaces)
    EAN
    0191073120976
    • A hundred and fifty grams published, the only weight on this shelf
    • An enlarged opening for the controls without removing the cover
    • A draped sheet rather than a fitted cover — no window and no eyepiece

    Best for: A long telephoto on a tripod in the field, where the cover has to blend in, fold to nothing and let the controls be reached.

    ≈ $52 / £38 / 37 €
    Check price on Amazon
  • Vanguard Alta RCM rain cover over a reflex with a 70-200 mm lens

    Vanguard Alta RCM, for a 70-200 mm f/2.8, size 2 of 4

    Twenty-two euros for a cover specified by the lens it fits — a 70-200 mm f/2.8 — rather than by any dimension, with a TPU window and a three-second setup.

    Lens length accommodated
    GIVEN AS A LENS RATHER THAN A FIGURE: a DSLR or mirrorless camera with a 70-200 mm f/2.8, in the first and fifth bullets. That is genuinely useful — the 70-200 f/2.8 is the standard fat telephoto, so anyone who owns one knows immediately — and it is the only cover on this shelf with no dimension at all. The page also prints the lens as "7-2 mm" twice, which is a typographic error for 70-200
    Eyepiece design
    A CLEAR TPU WINDOW, in the fourth bullet, and nothing more. TPU is the better window material — flexible, clearer and more scratch-resistant than PE film — and the 20 € K&F on this shelf adds an anti-fog coating to the same material
    Hand access
    Not described
    Material and seams
    NOT NAMED. Five bullets describe what the cover does and none says what it is made of — on a product whose entire function is keeping water out. Both the 20 € K&F and the 37 € NEEWER here name nylon
    Closure method
    Not described. The third bullet claims a three-second setup with no fumbling, which implies elastic rather than a zip, and the page does not say
    Packed size
    Not published
    Amazon reference
    B07N5KJWNB (same reference on 6 Amazon marketplaces)
    EAN
    4719856246208
    • Specified by the lens it fits, which is instantly checkable for a 70-200 owner
    • A clear TPU window, the better window material
    • No material named at all, on a rain cover

    Best for: A reflex or mirrorless body with a 70-200 mm f/2.8 fitted, from a range where a longer lens has its own size.

    ≈ £25 / 22 €
    Check price on Amazon

All camera hard cases