Skip to content

Minus thirty to plus eighty degrees

B&W International Type 4000, IP67, −30 to +80 °C, stackable

A hundred euros for an IP67 polypropylene case rated from −30 to +80 °C, stackable, with three layers of cubed foam and two 7 mm padlock eyes.

B&W International yellow Type 4000 case open with its cubed foam layers

B&W International Type 4000, IP67, −30 to +80 °C, stackable

A hundred euros for an IP67 polypropylene case rated from −30 to +80 °C, stackable, with three layers of cubed foam and two 7 mm padlock eyes.

Internal dimensions
NOT PUBLISHED, and it is the one specification this page owes. The 40 € HMF on this shelf publishes its interior, its exterior AND the split between base and lid; this page describes the foam that fills a space it never measures
Ingress rating
IP67, in the third bullet — dust-tight and protected against immersion to one metre for thirty minutes, the same standard as the HMF here
Interior type
THREE LAYERS of pre-cut CUBED foam, in the first bullet, plucked cube by cube to fit a camera, a drone, tools, electronics or measuring equipment, with lid and base foam completing the protection. Three layers is more material to work with than the single 95 mm block of the 40 € HMF
Pressure valve
YES, and AUTOMATIC, in the third bullet — paired there with the temperature range, which is the right pairing: air expands and contracts with heat as well as altitude, and a valve is what keeps the seal from doing the work
Latch and lock provision
TWO sturdy front catches holding the case closed, and TWO EYES OF 7 mm DIAMETER for padlocks, in the fifth bullet. Publishing the eye diameter is unusual and useful: it says which padlock will actually pass through
Wheels and handles
A RUBBERISED carry handle, in the fourth bullet, and a STACKABLE construction that saves space in a vehicle, a store or on a shelf. No wheels. Stackability is a working feature — cases that stack are cases that travel in a van without sliding
Empty weight
Not published, where the 40 € HMF gives 1.82 kg
Amazon reference
B00H3R5Z5S (same reference on 6 Amazon marketplaces)
EAN
0013039312914
  • Rated from −30 to +80 °C, the only temperature range in this catalogue
  • Three layers of cubed foam, with lid and base foam as well
  • No internal dimensions published, at 100 €

Best for: Equipment that travels in a vehicle through real cold or real heat, stacked with other cases and padlocked.

≈ £117 / 100 €
Check price on Amazon

Specifications

Internal dimensions
NOT PUBLISHED, and it is the one specification this page owes. The 40 € HMF on this shelf publishes its interior, its exterior AND the split between base and lid; this page describes the foam that fills a space it never measures
Ingress rating
IP67, in the third bullet — dust-tight and protected against immersion to one metre for thirty minutes, the same standard as the HMF here
Interior type
THREE LAYERS of pre-cut CUBED foam, in the first bullet, plucked cube by cube to fit a camera, a drone, tools, electronics or measuring equipment, with lid and base foam completing the protection. Three layers is more material to work with than the single 95 mm block of the 40 € HMF
Pressure valve
YES, and AUTOMATIC, in the third bullet — paired there with the temperature range, which is the right pairing: air expands and contracts with heat as well as altitude, and a valve is what keeps the seal from doing the work
Latch and lock provision
TWO sturdy front catches holding the case closed, and TWO EYES OF 7 mm DIAMETER for padlocks, in the fifth bullet. Publishing the eye diameter is unusual and useful: it says which padlock will actually pass through
Wheels and handles
A RUBBERISED carry handle, in the fourth bullet, and a STACKABLE construction that saves space in a vehicle, a store or on a shelf. No wheels. Stackability is a working feature — cases that stack are cases that travel in a van without sliding
Empty weight
Not published, where the 40 € HMF gives 1.82 kg
Amazon reference
B00H3R5Z5S (same reference on 6 Amazon marketplaces)
EAN
0013039312914

On the listing

Five bullets in capitals. Individually adaptable, three layers of pre-cut cubed foam easily fitted to a camera, drone, tools, electronics or measuring equipment, cubes pulled out for a snug recess, with lid and base foam completing all-round protection; robustly protected, an impact-resistant polypropylene shell guarding sensitive equipment from knocks and shocks, the individually fitted cubed foam holding the contents in place; water- and dust-protected to IP67 even in rain and dust, with an automatic pressure-equalisation valve and temperature resistance from −30 °C to +80 °C; everyday comfort, a rubberised carry handle for comfortable transport and a stackable construction saving space in a vehicle, store or on a shelf; and securely closed, two sturdy front catches holding the case shut, with two eyes of 7 mm diameter allowing it to be locked with a padlock.

Minus thirty to plus eighty

The only temperature range in this catalogue. Polypropylene goes brittle in cold and soft in heat, and a case in a vehicle meets both within a year.

Three layers of cubes, and foam above and below

More material than a single block, which means more chances to get the recess right — and each cube still comes out only once.

Seven millimetres of padlock eye

A figure, not a feature. It says which shackle passes through, and nothing else here publishes it.

Stackable, which matters in a van

Cases that stack do not slide. It is a working detail rather than a photographic one.

What a hundred euros does not publish

Its interior. The 40 € case on this shelf gives 30.5 by 23 by 14 cm, the base and lid split, and 1.82 kg.

Availability

Between 100 € and 122 € on the German, French, Italian and Spanish Amazon stores when this page was last checked.

The American and British Amazon stores carry it too, priced in local currency. Those amounts are deliberately absent from the range above, which reads euro stores only.

Everything in this section is the figure Keepa carried on the day of the last update to this page. Availability and prices shift without notice.

Prices quoted in this text were read on 13 September 2026. The live price is at the top of the page.

More camera hard cases

  • HMF ODK100 hard case open showing its pick-and-pluck grid foam

    HMF ODK100, 30.5 by 23 by 14 cm inside, IP67, 1.82 kg

    Forty euros for an IP67 case that publishes everything: 30.5 by 23 by 14 cm inside, split 10.5 and 3.5 between base and lid, three foam layers, 1.82 kg.

    Internal dimensions
    THE MOST COMPLETE FIGURES IN THIS CATALOGUE: 30.5 by 23 by 14 cm inside, and the fifth bullet goes further by splitting the depth — 10.5 cm in the base, 3.5 cm in the lid — inside an exterior of 34 by 29.5 by 15.5 cm measured INCLUDING the handle and catches. The split is what tells you whether a body with a lens fitted stands up in the base
    Ingress rating
    IP67, in the second bullet: dust-tight, and protected against immersion in water to one metre for thirty minutes. It is a standard rather than an adjective, and both cases on this shelf publish it
    Interior type
    THREE LAYERS, itemised in the third bullet: 95 mm of pre-cut grid foam — the pick-and-pluck kind, plucked cube by cube to the shape of the equipment — a 10 mm foam floor beneath it, and CONVOLUTED egg-crate foam in the lid to press down on whatever is below
    Pressure valve
    YES, a pressure-equalisation valve in the fourth bullet. A sealed case carried up a mountain or flown in a hold arrives at a different air pressure from the one it was closed at, and without a valve the lid either jams shut or strains its seal
    Latch and lock provision
    A folding carry handle and EYES FOR PADLOCKS, in the fourth bullet. Padlock eyes are what let a case be checked into a hold or left in a vehicle
    Wheels and handles
    A folding handle, no wheels — correct at this size. Thirty-four centimetres and 1.82 kg is a case that is carried
    Empty weight
    1.82 kg, PUBLISHED in the fifth bullet — the only empty weight on this shelf, and the figure that decides what an airline allowance leaves for the equipment
    Amazon reference
    B08K3JBWP7 (same reference on 5 Amazon marketplaces)
    EAN
    4010537103422
    • Internal dimensions published with the base and lid depths split out
    • Three foam layers named — pick-and-pluck, floor and convoluted lid
    • No wheels, though at 34 cm none is needed

    Best for: A body, two lenses and a drone taken somewhere wet, dusty or airborne, where the case has to be locked and its weight declared.

    ≈ £34 / 40 €
    Check price on Amazon

Elsewhere in the camera bag

  • JZK rain cover fitted over a reflex camera with its clear rear panel visible

    JZK 32 cm of lens, full-length zip, no flash space

    Nine euros for a cover taking 32 cm of camera and lens, with a full-length zip and a clear rear panel — and a title that admits there is no room for a flash.

    Lens length accommodated
    32 cm for camera AND lens together, in the first and second bullets — the second-longest on this shelf behind the 39 cm K&F. Thirty-two centimetres takes a reflex with a 70-200 mm zoom; it does not take a 400 mm. The figure is published twice, which on this shelf counts as emphasis
    Eyepiece design
    Not described. Nothing on the page says how the eye reaches the viewfinder — an eyepiece opening, a drawcord, a transparent panel — which on a reflex is how the picture gets composed
    Hand access
    Not described either. The fourth bullet covers the zip and the fifth the screen window, and neither says how a hand reaches the controls
    Material and seams
    Waterproof and dustproof, in the third bullet, usable in the rainy season, in the desert and at the beach. No fabric is named and no seam treatment described — and on a rain cover the seams are where water arrives first
    Closure method
    A FULL-LENGTH ZIP, in the fourth bullet, allowing the cover to be closed from underneath whether the camera is hand-held or on a tripod, without weakening the rain protection. A zip that runs the whole length is what lets the cover go on around a mounted camera rather than over it
    Packed size
    NOT PUBLISHED, as on four of the five covers here. A cover that does not fold small is a cover left at home
    Amazon reference
    B01MS6E4JX (same reference on 6 Amazon marketplaces)
    EAN
    6920484230592
    • Thirty-two centimetres of camera and lens, published twice
    • A full-length zip that closes from below, on a tripod or in the hand
    • The title states there is no space for a flash

    Best for: A reflex with a mid-length zoom in real rain, used on a tripod where the cover has to close underneath.

    ≈ £8 / 9 €
    Check price on Amazon
  • K&F Concept rain cover with its clear TPU window over a camera screen

    K&F CONCEPT 19 by 15 by 39 cm, TPU window, anti-fog

    Thirty-nine centimetres of depth, a TPU window with an anti-fog coating and a waterproof zip — the most thoroughly built cover on this shelf, at 20 €.

    Lens length accommodated
    THE DEEPEST CAPACITY HERE: 19 by 15 by 39 cm — width, height and depth — in the first bullet, which also asks the buyer to check the measurements before purchase. Thirty-nine centimetres of depth takes a long telephoto with a hood, and publishing all three dimensions is what lets a fat lens be checked as well as a long one
    Eyepiece design
    A HIGH-TRANSPARENCY TPU WINDOW over the display and the viewfinder, in the third bullet, with an ANTI-FOG COATING that prevents condensation forming even when the temperature changes, and a scratch- and oil-resistant surface. The anti-fog layer is unique on this shelf and it addresses the failure that actually happens: a cover in the rain is warm inside and cold outside, and a plain plastic window mists over exactly when it is needed
    Hand access
    Not described. The cover is closed by a zip and adjusted by velcro inside, and how the hands reach the controls is not stated
    Material and seams
    Water-repellent NYLON with a WATERPROOF ZIP, in the second bullet, said to protect against rain, snow, salt air and extreme weather. The zip is the part worth noting — an ordinary zip is a line of holes, and a waterproof one is a real construction choice. Seams are not described
    Closure method
    Three mechanisms, in the second and fourth bullets: the waterproof zip; an ADJUSTABLE VELCRO STRIP INSIDE that adapts to any lens diameter; and elastic bands with a NON-SLIP LEATHER TAB at the lens mount. The internal velcro is what makes one cover fit a 50 mm prime and a 300 mm zoom equally tightly
    Packed size
    Not a figure, but the fifth bullet states the property: light, foldable nylon that takes up hardly any space, named for hiking, action photography and demanding outdoor use
    Amazon reference
    B0F48271FG (same reference on 5 Amazon marketplaces)
    EAN
    6942052558327
    • Nineteen by 15 by 39 cm published — all three dimensions, 39 cm of depth
    • A TPU window with an anti-fog coating, unique on this shelf
    • Hand access is never described

    Best for: A long lens in sustained rain or salt air, where the window must not fog and the cover must grip whatever lens is fitted.

    ≈ £18 / 20 €
    Check price on Amazon
  • NEEWER PB020 camouflage rain cover over a telephoto lens on a tripod

    NEEWER PB020, 950 by 850 mm, 400 mm lens, 150 g, reversible camo

    A 950 by 850 mm nylon sheet at 150 g that reverses between two camouflage patterns and takes a 400 mm telephoto — a 950 by 850 mm sheet at 150 g, at 37 €.

    Lens length accommodated
    THE LONGEST ON THIS SHELF: lenses up to 400 mm in the title, with the third bullet putting camera and lens combined UNDER 600 mm. Those are focal lengths rather than centimetres — a 400 mm telephoto is roughly 35 cm of barrel — and a cover cut for one is a cover for wildlife work
    Eyepiece design
    Not described, and on this cover it matters less: a 950 by 850 mm sheet is draped and folded rather than fitted, so the photographer looks in under the edge rather than through a window
    Hand access
    AN ENLARGED OPENING, in the fourth bullet, giving access to the important camera functions without removing the cover. It is the only page on this shelf to describe hand access at all — four others leave it unstated
    Material and seams
    NYLON, waterproof, in the fifth bullet, credited with long-lasting protection. Seams are not described
    Closure method
    VELCRO fasteners, in the fourth bullet: the cover is pulled over the equipment and the velcro secures it. Simple, adjustable to any size, and the reason the same sheet fits a 200 mm and a 400 mm lens
    Packed size
    Not published as a folded figure — but the WEIGHT is: 150 g, in the fifth bullet, the only weight on this shelf. A hundred and fifty grams of nylon folds to about the size of a fist, which is what the same bullet means by easy to fold and perfect for photography on the move
    Amazon reference
    B0CTCXY92S (same reference on 6 Amazon marketplaces)
    EAN
    0191073120976
    • A hundred and fifty grams published, the only weight on this shelf
    • An enlarged opening for the controls without removing the cover
    • A draped sheet rather than a fitted cover — no window and no eyepiece

    Best for: A long telephoto on a tripod in the field, where the cover has to blend in, fold to nothing and let the controls be reached.

    ≈ $52 / £38 / 37 €
    Check price on Amazon

All camera hard cases